systemd-resolved has a compatibility interface for use with resolvconf
scripts when resolvectl is called from a symlink from resolvconf.
However, when tearing down the interface, cmd_down calls del_if and then
unset_dns. In the case of systemd-resolved, deleting the interface also
removes the systemd-resolved entry and causes resolvconf -d to fail when
resolvconf really is a symlink to resolvectl. This causes `wg-quick
down` and 'wg-quick@.service' to exit with failure.
Instead we use the resolvconf '-f' flag to ignore non-existent
interfaces, supported by both openresolv and sd-resolved resolvconf.
Signed-off-by: Ronan Pigott <rpigott@berkeley.edu>
[zx2c4: moved -f argument to end to remain compatible with Debian's resolvconf]
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
route(8) has always used the `-T` option to specify the
routing table; there is no `rdomain` option.
Signed-off-by: Ankur Kothari <ankur@lipidity.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This causes wg-quick up to wait for the monitor to exit before it exits,
so that launchd can correctly wait on it.
Reported-by: Cameron Palmer <cameron@promon.no>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
`wg-quick strip` prints the config file to stdout after stripping it of
all wg-quick-specific options.
This enables tricks such as `wg addconf $DEV <(wg-quick strip $DEV)`.
Signed-off-by: Luis Ressel <aranea@aixah.de>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Apparently Haiku has a misbehaving /dev/urandom.
While we're at it, simplify the function signature to completely succeed
or completely fail and make sure the caller checks the result.
Reported-by: Alexander von Gluck IV <kallisti5@unixzen.com>
Nitpicked-by: Aaron Jones <aaronmdjones@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The commit 7c833642 ("wg-quick: freebsd: allow loopback to work") was
supposed to make things better, but actually it just started sending
legitimate localhost traffic over the WireGuard interface, which is
really quite bad.
This reverts commit 7c833642dfa342218602ab18e7091e86408d2982.
Reported-by: Matt Smith <matt.xtaz@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Since wg-quick(8) calls wg(8) which does hostname lookups, we should
probably only run this after we're allowed to look up hostnames.
Reported-by: Anton Castelli <anton.c42@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
FreeBSD adds a route for point-to-point destination addresses. We don't
really want to specify any destination address, but unfortunately we
have to. Before we tried to cheat by giving our own address as the
destination, but this had the unfortunate effect of preventing
loopback from working on our local ip address. We work around this with
yet another kludge: we set the destination address to 127.0.0.1. Since
127.0.0.1 is already assigned to an interface, this has the same effect
of not specifying a destination address, and therefore we accomplish the
intended behavior.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This reverts commit 9d5baf7d1d14ca7eb0852b41566330259229d489.
Benoît Viguier has proofs that values will stay well within 2^53. We
also have an improved carry function that's much simpler.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This avoids another ip(8) invocation for little benefit.
Confirmed to work with iproute2 and busybox.
Signed-off-by: Aaron Jones <aaronmdjones@gmail.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
